# Angle to Angle

{% embed url="<https://youtu.be/ydRJMAiIYAQ>" %}

### Tools Needed for This Installation

{% columns %}
{% column %}

<figure><img src="/files/4tu6Jifo2MtbXOp6v2g5" alt=""><figcaption></figcaption></figure>
{% endcolumn %}

{% column %}

<figure><img src="/files/X1iTg0lllLgb0IH02LGL" alt=""><figcaption></figcaption></figure>
{% endcolumn %}

{% column %}

<figure><img src="/files/LxYbvuW2zhYjSOb0vhkk" alt=""><figcaption></figcaption></figure>
{% endcolumn %}

{% column %}

<figure><img src="/files/p043ZviFUzwkxiP4EX7h" alt=""><figcaption></figcaption></figure>
{% endcolumn %}
{% endcolumns %}

{% columns %}
{% column %}

<figure><img src="/files/qoNsTRzhoE3YZbVcrNzG" alt=""><figcaption></figcaption></figure>
{% endcolumn %}

{% column %}

<figure><img src="/files/MHBTf0vJK4m2I33Fs5in" alt=""><figcaption></figcaption></figure>
{% endcolumn %}

{% column %}

<figure><img src="/files/BNyg8MHUwXYrWfXZbhLC" alt=""><figcaption></figcaption></figure>
{% endcolumn %}

{% column %}

<figure><img src="/files/aAOyXGS9fWZ7qQtNzYou" alt=""><figcaption></figcaption></figure>
{% endcolumn %}
{% endcolumns %}

### Order of Installation and Hardware

Through hundreds of on site installations, we have come up with the best order to install posts into your system depending on what posts are being used. Please review the [Signature Post Order of Installation](/install/signature-cable-railing/post-order-of-installation.md) table and compare it against your order contents to find the best way for you to have an easy installation.

<figure><img src="/files/Zn8FwNGK5iMm7a2aLMhK" alt=""><figcaption></figcaption></figure>

### Installation Steps

{% columns %}
{% column %}

<figure><img src="/files/uiCu5noI03xwRBNJc2vl" alt=""><figcaption></figcaption></figure>

* Take the loose end of your cable spool and slide the cable through the posts on the run you are working on
* It is typically easiest to run the cable up through the bottom post towards the top post
* As you are running the cable through the posts, place the metal sleeves on the cable facing the post hole to which they will attach
* Steep Adhesive sleeves will attach to each 5/16" hole on an angled run
  {% endcolumn %}

{% column %}

<figure><img src="/files/B3jFQj2iDqE50i2mYW2S" alt=""><figcaption></figcaption></figure>

* Once the cable passes through the final post on the run, crimp a Threaded Crimp Fitting onto the end of the cable
* Crimp the Threaded Crimp Fitting then turn it 90° and crimp it again
  {% endcolumn %}
  {% endcolumns %}

{% columns %}
{% column %}

<figure><img src="/files/5G8osg0dfCMYDqLF6GO1" alt=""><figcaption></figcaption></figure>

* Slide a Angle Washer over the Threaded Crimp Fitting
* Thread a Tension Receiver onto the Threaded Crimp fitting four full turns
  {% endcolumn %}

{% column %}

<figure><img src="/files/sudQ45O8CR6oRY5KtTQa" alt=""><figcaption></figcaption></figure>

* Pull the cable back against the post so the Tension Receiver is pulled into the Angle Washer
* Ensure the Angle washer rests flush against the side of the post
  {% endcolumn %}
  {% endcolumns %}

{% columns %}
{% column %}

<figure><img src="/files/Hpuuq9wMsk49XZjsnKDT" alt=""><figcaption></figcaption></figure>

* Return to the other end of the run where the Angle Tension Kit will be installed nearest the spool, and pull the cable tight for the full run
* Place painter’s tape on the cable where the cable meets the inside edge of the post
  {% endcolumn %}

{% column %}

<figure><img src="/files/3ZfkEpGRBcanprZDWDEn" alt=""><figcaption></figcaption></figure>

* Use the side cutting tool located below the main crimping head to cut your cable
* Slide the cable through the cable cutter and cut the cable 3" - 4" extra past the outside edge of the post
  {% endcolumn %}
  {% endcolumns %}

{% columns %}
{% column %}

<figure><img src="/files/LfSnoq5axGT1QNl6Yz3f" alt=""><figcaption></figcaption></figure>

* Remove the cable from the post
* Add and mark 1½" past the painter’s tape
* Cut the cable on this mark
  {% endcolumn %}

{% column %}

<figure><img src="/files/KomDLG30BYTsIc3i2efq" alt=""><figcaption></figcaption></figure>

* Before continuing, confirm that all your needed sleeves are in place on the cable run
* This will be the last time you will be able to add sleeves on the cable
  {% endcolumn %}
  {% endcolumns %}

{% columns %}
{% column %}

<figure><img src="/files/Dh3im5bRo1OuGleLwG83" alt=""><figcaption></figcaption></figure>

* Crimp a Threaded Crimp fitting onto the second end of the cable
* Crimp the Threaded Crimp Fitting then turn it 90° and crimp it again
  {% endcolumn %}

{% column %}

<figure><img src="/files/JItO4A14Vj7rMhytcUAS" alt=""><figcaption></figcaption></figure>

* Insert the Threaded Crimp Fitting into the 5 /16" hole on the inside face of the post
* Then, insert the Tension Receiver through the Angle Washer and then into the ½" hole on the outside face of the post
* Meet both in the middle of the post and thread the Tension Receiver onto the Crimp Fitting four full turns
  {% endcolumn %}
  {% endcolumns %}

{% columns %}
{% column %}

<figure><img src="/files/9qKcWdIcCjvPXe5p1IOi" alt=""><figcaption></figcaption></figure>

* Slide the protective Neoprene Sleeve onto the cable near the post you are working on
* Firmly grasp the sleeve with pliers and use the supplied 5/32" Allen wrench to tighten the Tension Receiver only\
  snug enough to hold in place
  {% endcolumn %}

{% column %}

<figure><img src="/files/CebQgl4uvQwDXDUBi7Ta" alt=""><figcaption></figcaption></figure>

* Remove the plastic cover on the Adhesive Sleeves and firmly press the sleeve against the 5 /16" holes on the run
* After all the cable runs are done and the Adhesive Sleeves are placed, use the Allen wrench to tighten the remaining side of the cable run in sequence
* Holding the cable with the pliers & neoprene sleeve, tighten until the cable is taut and then turn the Tension Receiver another half turn

*\*Before tensioning any cable infill, please ensure all posts and handrail are fully installed*
{% endcolumn %}
{% endcolumns %}

***

### Get Help from Us

Is this not the product you're looking for? Troubleshoot your issue by contacting our customer service team. [866-432-0541](tel:8664320541) or <customerservice@viewrail.com>


---

# Agent Instructions: Querying This Documentation

If you need additional information that is not directly available in this page, you can query the documentation dynamically by asking a question.

Perform an HTTP GET request on the current page URL with the `ask` query parameter:

```
GET https://resources.viewrail.com/install/signature-cable-railing/tension-kit-installs/angle-to-angle.md?ask=<question>
```

The question should be specific, self-contained, and written in natural language.
The response will contain a direct answer to the question and relevant excerpts and sources from the documentation.

Use this mechanism when the answer is not explicitly present in the current page, you need clarification or additional context, or you want to retrieve related documentation sections.